Welcome Guest Search | Active Topics | Log In | Register

Official Standart Build Diary - Pack 9 Options
Gandale
#1 Posted : 27 July 2020 20:33:12

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding build
Groups: Administrators, Registered, Global Forum Support, Moderator, Official Builds, Administrator

Joined: 08/09/2012
Posts: 14,583
Points: 44,576
Location: Aberdeen
Imperial Yacht Standart, Pack 9, Stages 79-88.

Stage 79 Contents: Parts Fret


Refer to the instructions to aid the identification of the parts used in this stage.

Remove parts A, B and C from the forward superstructure fret supplied with this stage and sand the edges smooth. Take one of the pieces ‘B’ and glue into position on part ‘A’, ensure it is the correct way round and square. Glue the second piece ‘B’ into piece A, parallel to the first. Test-fit and glue piece ‘C’ at the end of ‘A’, between the two ‘B’ pieces.

Now remove pieces D, E and F from the fret and sand the edges smooth. Test-fit and glue piece ‘D’ into ‘A’ and at the ends of pieces ‘B’. Test-fit and glue the two pieces ‘E’ either side of ‘D’, and into ‘A’. Now test-fit and glue piece ‘F’ at the end of ‘A’, between the two pieces ‘E’. When the glue has dried completely, sand the superstructure smooth.

Retrieve the two skylights assembled in stage 57, Hold one against the side of the superstructure and mark the end onto the side. Repeat on the other side. Cut a length of 1x3mm wooden strip to fit from the mark just made to the end of the superstructure. Then cut another length to fit vertically, ending 3mm below the top. Glue the two pieces into place then repeat on the other side. Now glue two more lengths of 1x3mm wooden strip along the bottom edge of the superstructure, at the other end.

Stage complete.

Store any unused parts in a labelled bag for future use.
Gandale attached the following image(s):
79-1.JPG
79-2.JPG
79-3.JPG
79-4.JPG
79-5.JPG
79-6.JPG
79-7.JPG
79-8.JPG
79-9.JPG
79-10.JPG
79-11.JPG
79-12.JPG
79-13.JPG
79-14.JPG
79-15.JPG
Gandale
#2 Posted : 01 August 2020 16:42:34

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding build
Groups: Administrators, Registered, Global Forum Support, Moderator, Official Builds, Administrator

Joined: 08/09/2012
Posts: 14,583
Points: 44,576
Location: Aberdeen
Stage 80 Contents: Etch Parts Fret and Davits.

The instructions doesn't mention this but I decided to paint the inner bulwarks gloss black at this stage. Easier to paint the now before the capping is glued in place.

Remove the parts from the fret supplied with stage 63 and retrieve the seven wooden strips also supplied with stage 63. Sand all these items smooth then apply a coat of primer and paint them matt white.

Glue the bow piece onto the foredeck, the piece should overlap the forward edge by 1mm. Take the two stern pieces, test-fit and glue into position, overlapping the aft edge slightly. Continue the rail forward from the two pieces just fitted, by gluing the painted 2x3mm strips on top of the bulwarks, on both sides. Cut a small length of 2x3mm wooden strip to fit on the bulwark up to the gap, repeat on the other side. Now glue another strip from the other side of the gap forward, do the same on the other side. Glue two 2x3mm strips from the foredeck aft along the bulwarks, covering the openings. Then cut two more lengths of 2x3mm strips to complete the rails on either side.

Remove the circle from the fret supplied with stage 64 and the frame piece from the etch fret supplied with this stage. Curve the frame piece to fit around the wooden circle. Turn the tabs on the cylindrical piece inward, then separate and file smooth the circular etch piece from the fret. Turn the cylindrical piece over and glue the etch circle inside it, on the inward-turned tabs. Separate the stairs from the fret and carefully fold up the railings. Glue the ladder to the assembly. When dry, paint the assembly with metal primer, then apply a coat of matt white paint. Paint the steps brown and the railing mahogany.

Stage complete.

Store any unused parts in a labelled bag for future use.
Gandale attached the following image(s):
80-1.JPG
80-2.JPG
80-3.JPG
80-4.JPG
80-5.JPG
80-6.JPG
80-7.JPG
80-8.JPG
80-9.JPG
80-10.JPG
80-11.JPG
80-12.JPG
80-13.JPG
80-14.JPG
80-15.JPG
80-16.JPG
80-17.JPG
80-18.JPG
80-19.JPG
80-20.JPG
Gandale
#3 Posted : 03 August 2020 08:33:57

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding build
Groups: Administrators, Registered, Global Forum Support, Moderator, Official Builds, Administrator

Joined: 08/09/2012
Posts: 14,583
Points: 44,576
Location: Aberdeen
Stage 81 Contents: Brass Wire, Vent and Stanchions

Retrieve the stern superstructure and drill five 0.75mm holes along the narrower edge of the deck. the holes should be 1mm away from the edge of the deck planking, with the outer two holes positioned 3mm in on either side, spacing the rest of the holes evenly.

Separate the stanchions from the fret and file to remove any burrs. Test-fit the stanchions into the holes just drilled, making sure the tops of the stanchions are all aligned. Adjust the heights of them if necessary, then glue into place. Now drill four 0.75mm holes in the deck along the port side, 4mm forward of those just fitted. The last one should be in line with the front of the overhang at the side. Test-fit and glue four stanchions into the holes, then repeat on the starboard side of the superstructure. Drill seven more holes along the starboard side of the superstructure as shown in step 7 of the instructions, then test-fit and glue stanchions into the holes.

Retrieve the platform assembled in stage 80 and glue it between the compass stand and the square hole in the deck. Retrieve the binnacle from stage 25 and glue it forward of the centre line of the circular platform.

Paint a strip of 1x3mm wooden strip mahogany, then paint the cleats from stage 61 with metal primer. When dry, paint the cleats brass. Cut the painted wooden strip into eight 13mm lengths, then glue lengths together in sets of two to make four platforms. Glue the cleats into the centre of the platforms then paint the cut ends mahogany. Glue the fours assembled cleats into the positions on either side of the main deck, as shown in step 13 of the instructions.

Stage complete.

Store any unused parts in a labelled bag for future use.
Gandale attached the following image(s):
81-1.JPG
81-2.JPG
81-3.JPG
81-4.JPG
81-5.JPG
81-6.JPG
81-7.JPG
81-8.JPG
81-9.JPG
81-10.JPG
81-11.JPG
81-12.JPG
81-13.JPG
81-14.JPG
Gandale
#4 Posted : 03 August 2020 20:18:42

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding build
Groups: Administrators, Registered, Global Forum Support, Moderator, Official Builds, Administrator

Joined: 08/09/2012
Posts: 14,583
Points: 44,576
Location: Aberdeen
Stage 82 Contents: Brass Wire, Vent and Stanchions

Drill twelve 0.75mm holes along the starboard side of the superstructure. The holes should start 12mm forward of the last stanchion fitted and the rest spaced every 12mm. Separate the stanchions from the etch fret and file smooth. Test-fit the stanchions the holes just drilled, making sure that they are all the same height. When all the stanchions are aligned, glue them into place.

Now drill seven holes along the front of the deck, 1mm in from the edge of the planking. The outer holes should be positioned 4mm in from the sides, with the rest of the holes 7mm apart. Test-fit and glue stanchions into the holes, ensuring that they are all aligned. The remaining stanchion should be glued into a hole drilled in the port side of the deck, as shown in step 7 of the instructions. Make sure it is aligned with the others.

Retrieve the boiler room assembly from stage 67. Test-fit the two newest vents into position. Retrieve the second boiler room assembly and drill six holes in it at the positions shown in step 9 of the instructions. Test-fit the funnel and two vents along the centre of the boiler room.

Retrieve the clear plastic sheet and cut two 10mm wide strips, long enough to fit the length of the inside of the boiler rooms. Glue both lengths inside one of the boiler rooms, underneath the skylights. Now repeat this on the second boiler room.

Stage complete.

Store any unused parts in a labelled bag for future use.
Gandale attached the following image(s):
82-1.JPG
82-2.JPG
82-3.JPG
82-4.JPG
82-5.JPG
82-6.JPG
82-7.JPG
82-8.JPG
82-9.JPG
82-10.JPG
82-11.JPG
82-13.JPG
Gandale
#5 Posted : 04 August 2020 22:55:25

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding build
Groups: Administrators, Registered, Global Forum Support, Moderator, Official Builds, Administrator

Joined: 08/09/2012
Posts: 14,583
Points: 44,576
Location: Aberdeen
Stage 83 Contents: Brass Wire, Vent and Stanchions

Drill 18 more 0.75mm holes in the aft superstructure deck, going forward to the front of the deck. All the holes along the side should be at a distance of 12mm from each other. Separate 18 stanchions from the fret and remove any burrs with a fine file. Test-fit the stanchions into the new holes then glue into place ensuring that they are aligned.

Retrieve the windlass from stage 74 and glue it to the deck, 20mm aft of the rectangular cut out. Now glue the compass from stage 43 to the deck, 5mm forward of the raised stern section. Glue the two binnacles from stage 29, 4mm away from the compass on either side, 3mm forward of the raised stern section. Glue the helm from stage 63 onto the raised stern section, making sure it is central.

Now paint the two fairleads supplied with stage 62 brass, then glue onto the rail, either side of the stern, 25mm away from the centre line.

Cut two 17x48mm pieces of the clear plastic sheet. Mark lines across them, 5mm in from either side. Score along the lines making sure you don’t cut all the way through, then bend the end pieces up 90 degrees. Glue the pieces of plastic inside the two hatches assembled in stages 42 and 47.

Stage complete.

Store any unused parts in a labelled bag for future use.

Gandale attached the following image(s):
83-1.JPG
83-2.JPG
83-3.JPG
83-4.JPG
83-5.JPG
83-6.JPG
83-7.JPG
83-8.JPG
83-9.JPG
83-10.JPG
83-11.JPG
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.131 seconds.
DeAgostini