Welcome Guest Search | Active Topics | Log In | Register

Porsche 911 Carrera customised build - pack 9 Options
Tomick
#1 Posted : 03 July 2018 21:30:31

Rank: Pro

Groups:

Joined: 24/08/2009
Posts: 44,244
Points: -6,498
Another instalment..Cool
roymattblack
#2 Posted : 03 July 2018 21:34:54

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalOutstanding Build: An award for an outstanding build
Groups: Registered, Moderator, Administrators, Global Forum Support

Joined: 04/06/2011
Posts: 2,804
Points: 8,567
Location: ipswich
PACK 9

This pack of parts deals predominantly with the front of the car.
To begin, the fuel tank is fitted.
The rubber grommet around the sender unit on top of the tank can be highlighted using a fine black marker pen.
Also, Googling for reference pictures shows that many 911’s had silver or black fuel tanks so you could repaint the tank if you wish.

The brake fluid reservoir can be detailed by adding two pipes to the bottom.
These can be attached either by just gluing the pipes up inside the cavity underneath, or as was done here, the cavity was filled with resin.
As the resin begins to set, two pieces of wire are set into it.
The hoses can then be glued onto the wires.
Hose clips can be made using self-adhesive aluminium tape strips.
The fixing band was also foiled silver after removing the noticeable mould seam and sprue pip.

The fixing screws are also painted silver in this case.
The batteries are assembled next but due to the way box shapes are injection moulded, the sides of the battery have a rather prominent slope to them.
This can be alleviated somewhat by filing the sides of the battery into a more regular box shape.
The lower flange can also be added at the sides, using small pieces of plastic strip.
If you wish, battery decals can be added to detail them a little more.
The decals can be found on Ebay.

Drill small holes in the battery terminals so that the leads can be added.
Fix the batteries into the car.

A length of wiring loom can be made using a piece of thicker red wire for the battery, and a few thin wires to lead to the front of the car.
Bind the wires as shown in the picture using surgical tape blackened with a marker pen.

The wiring can be attached to the bodywork using small dots of cyano glue.
Feed the rear of the cable through the opening at the back of the bay as shown in the picture and cut off any excess.
The front thinner wires can be wrapped around the front of the body panel and held in place with tape.

The other battery and wires are attaches as shown in the pictures.
The two front wings of the model are assembled as per the instructions.
However, you can cut down the height of the black aerial grommet so that the silver aerial part sits much closer to the body.
roymattblack attached the following image(s):
P1015799.JPG
P1015800.JPG
P1015801.JPG
P1015804.JPG
P1015809.JPG
P1015812.JPG
P1015813.JPG
P1015818.JPG
P1015820.JPG
P1015824.JPG
P1015825.JPG
P1015826.JPG
P1015828.JPG
P1015829.JPG
P1015832.JPG
P1015834.JPG
P1015836.JPG
P1015838.JPG
P1015840.JPG
P1015839.JPG
P1015841.JPG
P1015843.JPG
P1015844.JPG
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.056 seconds.
DeAgostini