Welcome Guest Search | Active Topics | Log In | Register

JohnM's Victory Build - Restarted Options
jmmx15
#1 Posted : 22 June 2021 21:03:06

Rank: Beginner Level 2

Groups: Registered

Joined: 22/10/2015
Posts: 10
Points: 20
Location: Crawfordville, FL, US
Hi All, I've been reading through your diary's as I've been getting Ye Olde Shipyard restarted to continue working on my Victory. I had started it a few years ago and then we moved and life has interfered with the process. I've now got a fairly functional work area and have restarted.

When I left off, I had all the ribs installed and the lower deck. I'm at the point of getting ready to start fairing the hull. Before I do it, I have some basswood pieces that I'm going to glue into the voids between the bow formers and between the last 2 ribs at the stern. I'd read an article on fairing that suggested it and it makes sense to me!

Before I start the fairing and planking, I decided to build the 4 small boats. I've finished the launch (pictures attached) and am priming the cutter, it's thwart supports, floorboards and thwarts---it's almost done. Once I've finished that I'll do the pinnace and barge. I figured these would give me a good introduction to planking. I'm not sure how much I've gleaned on planking with the small boats. I think planking them is a fairly different animal than planking the Victory!

For now, I have a few questions as I restart and continue on the small boats:

1. How do you paint the brass floorboards in the boats? I wasn't happy with whatever I did on the launch but it won't be seen when finished. For the other boats I'm thinking of trying to scuff up the brass with a sanding stick, then very lightly prime it with my airbrush. After that I'm on the fence about trying to brush paint them or airbrush them. My ears are open for suggestions!

2. Now that the launch is finished, and will sit with it's 3 brothers for quite a while, should I lacquer or varnish it? I'm also wondering about spraying them with Future floor polish. It's used quite often by plastic modelers to protect their finished work

3. What do you think of the Victory add ons from Woody's Modelworks
https://www.woodysmodelworks.co.uk ? Some of them have my interest including the Gallery, Bow Detail, Beakhead enhancement, Entry Ports, Cabins, buckets and Water Level markers (I'm going to tile my hull) kits

4. I've been using an electric plank bender for the small boats. I burnt myself once and found that I almost need 3 hands to use it with the form! Part of the solution may just be to put the form in a vice. I'm going to give that a try on the next boat. What has been your experience with the electric plank bender vs. the crimper with the razor blade?

5. Can you also please point me to any good discussions about the use of planking clamps, pins, binder clips etc. when doing the hull planking? I'm leaning towards binder clips and limited use of pins.

That's it for now, hopefully I can finish the cutter soon and get on to the other 2 boats. I actually think I might do an assembly line for the cannons and the anchors before heading over to the ship

Regards
jmmx15 attached the following image(s):
20210420_105545.jpg
20210420_105550.jpg
20210420_105556.jpg
20210420_105611.jpg
goddo
#2 Posted : 22 June 2021 22:42:29

Rank: Vice-Master
Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 21/04/2011
Posts: 667
Points: 1,994
Location: Buckinghamshire
Hi John,
Welcome back to the Victory build and look forward to watching your progress.
I'll leave the answers to your questions to the more experienced members on here.
Good luck.
Chris
jmmx15
#3 Posted : 23 June 2021 16:26:51

Rank: Beginner Level 2

Groups: Registered

Joined: 22/10/2015
Posts: 10
Points: 20
Location: Crawfordville, FL, US
When building the 18' Cutter I came across a problem in the instructions. Under the Pack 12, Stage 118 instructions under the heading "Fitting out the 18 foot Cutter you are told to cut two (2) 105 mm strips for the thwarts. Before I cut these, I checked the measurement (I'm more used to inches than mm).

Turns out my Cutter is only just over 65 mm in length. 105 mm was going to be just a bit to long! After trimming and testing, my thwarts ended up being just under 60 mm. For those who've reached the Cutter, which is more of a bear to plank than the Launch, I suggest start your thwarts at 61 - 61.5 mm and trim down from there

Hope this helps at least one person trying to build the Cutter with sausage fingers like me!

--John
Gandale
#4 Posted : 23 June 2021 23:11:34

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Administrators, Registered, Global Forum Support, Moderator, Official Builds, Administrator

Joined: 08/09/2012
Posts: 15,146
Points: 46,120
Location: Aberdeen
Hi John, welcome back.. great to have you with us again. Looks like you're doing a great job on the ships boats, lovely work....Cool Cool Cool

I'll try to answer each of your questions in turn.

jmmx15 wrote:


1. How do you paint the brass floorboards in the boats? I wasn't happy with whatever I did on the launch but it won't be seen when finished. For the other boats I'm thinking of trying to scuff up the brass with a sanding stick, then very lightly prime it with my airbrush. After that I'm on the fence about trying to brush paint them or airbrush them. My ears are open for suggestions!

My method was to lightly sand the surface with fine grade sandpaper. Then brushed on a coat of Mr Hobby Mr Metal primer and left to cure for 2 days. Using my airbrush I then gave a fine dusting of matt black paint. Left to dry then fitted to the boats.

2. Now that the launch is finished, and will sit with it's 3 brothers for quite a while, should I lacquer or varnish it? I'm also wondering about spraying them with Future floor polish. It's used quite often by plastic modelers to protect their finished work

Either or... My preference was to use Vallejo matt and silk varnish applied with my airbrush. Would suggest you try painting and varnishing some test pieces to see if it turns out the way you want. Worked for me....

3. What do you think of the Victory add ons from Woody's Modelworks
https://www.woodysmodelworks.co.uk ? Some of them have my interest including the Gallery, Bow Detail, Beakhead enhancement, Entry Ports, Cabins, buckets and Water Level markers (I'm going to tile my hull) kits

Have never tried any of them so would be unfair of me to comment except to say that some of them do look good...

4. I've been using an electric plank bender for the small boats. I burnt myself once and found that I almost need 3 hands to use it with the form! Part of the solution may just be to put the form in a vice. I'm going to give that a try on the next boat. What has been your experience with the electric plank bender vs. the crimper with the razor blade?

I've used a number of methods to bend planks and have always reverted to using an electric plank bender. Find the strips will bend very easily when soaked in warm water until pliable. Once I have the necessary bend then I'll temporarily pin the plank in place and leave to dry, then shape and fit. There are many videos on the tube showing how to bend and fit strips, some very good viewing to be found there...

5. Can you also please point me to any good discussions about the use of planking clamps, pins, binder clips etc. when doing the hull planking? I'm leaning towards binder clips and limited use of pins.

I don't like pinning directly through planking strips if I can help it, I prefer to use map pins, pinned to the side of the plank into the ribs then removing the pins when the glue has dried. I compiled a topic on this very subject that you may find interesting..

https://forum.model-spac...spx?g=posts&t=25807



Hope you find the answers useful.

Regards

Alan

jmmx15
#5 Posted : 24 June 2021 12:59:02

Rank: Beginner Level 2

Groups: Registered

Joined: 22/10/2015
Posts: 10
Points: 20
Location: Crawfordville, FL, US
Thank you Alan for taking the time to answer my questions, of course, I have a follow up or 2!

How long did you soak your planks for? On the boats I found that just running them under the tap for a few seconds did the job but am sure that won’t work for the ship’s planks!

Can you attach more than one row of planks at a time using the map pins? Won’t they introduce e a gap, though very small between the rows?

Can you think of any major gotchas that you or others have come across during your build? I’m thinking of things like the cannons on the upper deck and their gun ports not lining up vertically? Or doing certain tasks earlier than what the manual says due to easier access?

I think the first few lessons I’ve learnt is that the plank bender will burn you, don’t scrimp on a cheap set of calipers, manicure sticks are awesome, get a good set of micro drill bits, and making a drawing of where the thwarts and oar cutouts go relative to the ribs really helps and the Dremel tool used in moderation is your friend!

—John
Gandale
#6 Posted : 28 June 2021 23:16:04

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Administrators, Registered, Global Forum Support, Moderator, Official Builds, Administrator

Joined: 08/09/2012
Posts: 15,146
Points: 46,120
Location: Aberdeen
jmmx15 wrote:
Thank you Alan for taking the time to answer my questions, of course, I have a follow up or 2!

How long did you soak your planks for? On the boats I found that just running them under the tap for a few seconds did the job but am sure that won’t work for the ship’s planks!

Can you attach more than one row of planks at a time using the map pins? Won’t they introduce e a gap, though very small between the rows?

Can you think of any major gotchas that you or others have come across during your build? I’m thinking of things like the cannons on the upper deck and their gun ports not lining up vertically? Or doing certain tasks earlier than what the manual says due to easier access?

I think the first few lessons I’ve learnt is that the plank bender will burn you, don’t scrimp on a cheap set of calipers, manicure sticks are awesome, get a good set of micro drill bits, and making a drawing of where the thwarts and oar cutouts go relative to the ribs really helps and the Dremel tool used in moderation is your friend!

—John


No problem at all John, am happy to be of assistance whenever possible.

Soaking the planking strips - how long they should be soaked for really depends on the type of wood. I found the birch strips provided in the Victory kit would need to be soaked in warm water for some 20-30 minutes. I soak until the strips become pliable.

Map Pins - my method is to attach a strip and pin along the upper edge. By the time you have one row fitted and start fitting the next row the glue will have taken hold. This means I remove the pins as I go and refit the pins to hold the next row.

As for glitches, follow the Official Build Diary. This highlights any potential pitfalls that were identified during the course of the build and things that need to be looked out for. Lot of builders didn't ensure the stern ribs, rib 30 was fully seated. They didn't notice this rib is prone to moving especially if you turn the hull over before letting the glue set. Check the seating of these stern ribs often until they are firmly glued in place.

Hope this helps..

Regards

Alan


tom.ganc
#7 Posted : 20 November 2021 19:05:09

Rank: Pro

Build-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 25/03/2010
Posts: 383
Points: 1,090
Location: Hyde
It's great to hear this news, we can't wait to see more pics from your build.

Of course we will be happy to help if you get stuck.

Happy building

Tom
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.188 seconds.
DeAgostini