Welcome Guest Search | Active Topics | Log In | Register

Rossi Yamaha YZR-M1 Official Build Diary - Pack 12 (UK) Options
Spal
#1 Posted : 29 December 2019 17:38:51

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Official Builds, Registered

Joined: 19/06/2013
Posts: 4,589
Points: 13,620
Location: West Yorkshire
Pack 12 contains parts for stages 44-46

Stage 44

Contents:Swingarm axle, Nut cover, Nut.

Insert the nut into the circled hole in the left frame.Place the right frame into position over the holes on the engine and left frame assembly. Once the holes of both parts are aligned, tighten two type V screws into the forward mounting holes, another two into the two rear holes and finally two into the front of the frame.Fix the underside of the frame with a type B screw.

Stage complete, carefully store any remaining parts in a stage labelled bag.
Spal attached the following image(s):
IMGL3033.JPG
IMGL3034.JPG
IMGL3035.JPG
IMGL3036.JPG
IMGL3037.JPG
IMGL3039.JPG
IMGL3040.JPG
IMGL3041.JPG
IMGL3042.JPG
Spal
#2 Posted : 29 December 2019 17:43:50

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Official Builds, Registered

Joined: 19/06/2013
Posts: 4,589
Points: 13,620
Location: West Yorkshire
Stage 45

Contents:Lever, Linkage, Type P screws, Type N screws, Gas cartridge, Valves.

Insert the linkage between the circled holes of the lever, noting the correct positioning. Tighten a type N screw through the aligned holes, allowing the linkage to remain free to move. Position the lever between the two sides of the lower crossmember, inserting a type P screw through the aligned holes and tightening it sufficiently to allow it to move freely.
Push the gas cartridge onto the pin of the valves. Insert the two pins on the valves into the two holes in the shock absorber. Secure with a little glue if necessary.

Stage complete, carefully store any remaining parts in a stage labelled bag.
Spal attached the following image(s):
IMGL3044.JPG
IMGL3047.JPG
IMGL3048.JPG
IMGL3049.JPG
IMGL3050.JPG
IMGL3051.JPG
IMGL3052.JPG
IMGL3053.JPG
IMGL3055.JPG
IMGL3056.JPG
IMGL3058.JPG
Spal
#3 Posted : 29 December 2019 17:46:31

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Official Builds, Registered

Joined: 19/06/2013
Posts: 4,589
Points: 13,620
Location: West Yorkshire
Stage 46

Contents:Radiator bracket, Lambda probe pipes x 4, Bracket,Cable guides x 2, Type S screws, Type V screws.

Retrieve the radiator assembly. Insert the pins on the two cable guides into the holes in the top of the radiator.
Retrieve the exhaust assembly (Stage 15) and push two of the Lambda probe pipes onto the first two probes,fit the two remaining pipes onto the other two lambda probes. Retrieve gaskets L1 and R1 supplied with Stage 38, they will be fitted to the two outer manifolds. Align the ends of the manifolds with the corresponding holes in the engine and insert the manifolds into the holes in the engine. To secure the exhaust pipe to the engine, locate the three circled holes and prepare the bracket supplied with this stage. Use two type V screws and one type S screw to fix the bracket to the exhaust and the frame, noting the correct positioning.

Stage complete, carefully store any remaining parts in a stage labelled bag.
Spal attached the following image(s):
IMGL3059.JPG
IMGL3060.JPG
IMGL3061.JPG
IMGL3062.JPG
IMGL3066.JPG
IMGL3067.JPG
IMGL3068.JPG
IMGL3070.JPG
IMGL3072.JPG
IMGL3073.JPG
IMGL3074.JPG
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 1.532 seconds.
DeAgostini