Welcome Guest Search | Active Topics | Log In | Register

4 Pages <1234>
Graham's Easy Rider Build Options
bugsec
#41 Posted : 28 December 2018 00:25:29

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Build Stage 12 - The upper exhaust pipe.
Parts required:
A, B, C and D from Parts 11

Also required:
The upper silencer from Stage 11.

Brackets A and C are fitted to the exhaust pipe. The exhaust pipe is attached to the silencer and held with bracket D.

bugsec attached the following image(s):
031.jpg
032.jpg
033.jpg
034.jpg
bugsec
#42 Posted : 28 December 2018 00:26:41

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Build Stage 13 - The lower silencer.
Parts required:
A, B, C, D and E from Parts 12

Also required:

The two parts of the silencer are fitted together and the brackets added to hold in place.

bugsec attached the following image(s):
035.jpg
036.jpg
bugsec
#43 Posted : 28 December 2018 00:27:41

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Build Stage 14 - The lower exhaust pipe.
Parts required:
A, B and C from Parts 13; F from Parts 14.

Also required:
The lower silencer from Stage 13.

The two exhaust pipe sections are fitted to the silencer and held using the brackets.

bugsec attached the following image(s):
037.jpg
038.jpg
039.jpg
040.jpg
bugsec
#44 Posted : 28 December 2018 00:28:46

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Build Stage 15 - The horn.
Parts required:
A, B, C, D and E from Parts 14.

Also required:

The cable from the circuit board if fed through the horn case then the circuit board is fitted into the recess in the case. The horn cover is fitted onto the front of the horn case then the mounting plate is fitted to the rear of the horn case.

bugsec attached the following image(s):
041.jpg
042.jpg
043.jpg
044.jpg
Tomick
#45 Posted : 28 December 2018 08:49:28

Rank: Pro

Groups:

Joined: 24/08/2009
Posts: 45,863
Points: -6,838
Nice update and looking good Cool
Markwarren
#46 Posted : 28 December 2018 09:23:31

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Administrators, Global Forum Support, Registered, Moderator, Official Builds

Joined: 04/01/2016
Posts: 5,296
Points: 16,183
Location: Northamptonshire, England
Coming on very nicely. Great update. Cool

Mark
Gandale
#47 Posted : 28 December 2018 10:55:57

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Administrators, Registered, Global Forum Support, Moderator, Official Builds, Administrator

Joined: 08/09/2012
Posts: 14,764
Points: 45,122
Location: Aberdeen
Very nice work indeed, making beautiful progress....Drool Drool

Regards

Alan
arpurchase
#48 Posted : 28 December 2018 11:04:31

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 27/09/2011
Posts: 15,209
Points: 46,177
Location: Dudley
BigGrin All looking good from here and nicely doneCool
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

bugsec
#49 Posted : 28 December 2018 14:18:02

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Thanks for looking in and the kind comments guys. My New Year Resolution will be to keep up to date with builds and build diaries LOL

Graham
pemberg
#50 Posted : 05 January 2019 23:13:46

Rank: Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 20/04/2012
Posts: 1,787
Points: 5,302
Location: Thurso
Your build is coming along very nicely, good work.

Graeme
Spal
#51 Posted : 06 January 2019 00:58:41

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Official Builds, Registered

Joined: 19/06/2013
Posts: 4,589
Points: 13,620
Location: West Yorkshire
Nicely done Graeme BigGrin will be following your build.

Al
bugsec
#52 Posted : 16 March 2019 13:34:07

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Thanks all for the kind comments.

Pack 04 contains Stages 16 - 21

Parts supplied:
Parts 16:
A - Number Plate
B - Number plate mount and rear light
C - Screws

Parts 17:
A - Left body frame

Parts 18:
A - Clutch linkage
B - Clutch linkage plate
C - U-shaped clamp
D - Screws and fittings
E - Spring
F - Linkage road

Parts 19:
A - Gearshift pedal plate
B - Linkage arm
C - Linkage
D - Gearshift pedal
E - Pedal rubber
F - Fittings

Parts 20:
A - Right body frame
B - Screws

Parts 21:
A - Footbrake plate
B - Footbrake pedal
C - Brake pivot
D - Linkage
E - Fittings

bugsec attached the following image(s):
Parts 16.jpg
Parts 17.jpg
Parts 18.jpg
Parts 19.jpg
Parts 20.jpg
Parts 21.jpg
bugsec
#53 Posted : 16 March 2019 13:36:14

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Build Stage 16 - The number plate
Parts required:
A, B and C from Parts 16

Also required:
The sissy bar from Parts 15.

The number plate mount is fixed to the sissy bar using the provided screws. The number plate is then fitted to the number plate mount using the pins on the number plate.

bugsec attached the following image(s):
045.jpg
046.jpg
bugsec
#54 Posted : 16 March 2019 13:37:14

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Build Stage 17 - The body frame
Parts required:
A from Parts 17 and A and B from Parts 20

Also required:

The two frames halves are aligned then fixed using the screws provided.

File Attachment(s):
047.jpg (268kb) downloaded 27 time(s).
bugsec
#55 Posted : 16 March 2019 13:40:22

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Build Stage 18 - The clutch linkage
Parts required:
A, B, D (some parts), E and F from Parts 18

Also required:

The bolt with the eye is fixed to the clutch linkage using the nuts. The clutch linkage and the clutch linkage plate are fixed togetjer using the washer screw. The linkage rod is secured to the linkage plate with nut and bolt. Finally the spring is connected between the eyebolt and the post on the linkage plate.
The remaining parts are stored for later use.

bugsec attached the following image(s):
048.jpg
049.jpg
050.jpg
051.jpg
052.jpg
bugsec
#56 Posted : 16 March 2019 13:41:32

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Build Stage 19 - The rear brake
Parts required:
A, B, C, D, E and F from Parts 19

Also required:

The pedal rubber is fitted to the gearshift pedal. The gearshift pedal and linkage arm are then secured to the gearshift pedal plate using a washer screw. The post on the end of the linkage is fitted into the end of the linkage arm and secured with a nut and bolt.
The remaining parts are stored for later use.

bugsec attached the following image(s):
055.jpg
053.jpg
054.jpg
bugsec
#57 Posted : 16 March 2019 13:42:34

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Build Stage 20 - The footbrake
Parts required:
A, B, D and E (some parts) from Parts 21

Also required:

The bracket is attached to the linkage using the nut and bolt. The linkage is attached to the footbrake pedal using another nut and bolt. The footbrake pedal is attached to the footbrake plate using the bolt supplied.

bugsec attached the following image(s):
056.jpg
057.jpg
058.jpg
bugsec
#58 Posted : 16 March 2019 13:43:45

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Build Stage 21 - The brake pivot
Parts required:
C and E (some parts) from Parts 21

Also required:

The pin is inserted into the brake pivot.

All unused parts from the pack are stored for later use.

bugsec attached the following image(s):
059.jpg
bugsec
#59 Posted : 16 March 2019 18:16:22

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Pack 05 contains Stages 22 - 27

Parts supplied:
Parts 22:
A - Brake disc
B - Sprocket

Parts 23:
A - Drive chain

Parts 24:
A - Crankcase
B - Tappet guide
C - Plug
D - Washer screws

Parts 25:
A - Transmission case
B - Screws

Parts 26:
A - Screws
B - Oil filter top
C - Oil filter

Parts 27:
A - Screws
B - Transmission cover
C - Distributor base
D - Gasket
E - Distributor

bugsec attached the following image(s):
Parts 22.jpg
Parts 23.jpg
Parts 24.jpg
Parts 25.jpg
Parts 26.jpg
Parts 27.jpg
bugsec
#60 Posted : 16 March 2019 18:18:12

Rank: Pro
Red Medal: Red MedalBuild-Diary Medal: Build-Diary Medal of Honour
Groups: Registered

Joined: 04/06/2010
Posts: 332
Points: 1,000
Location: Bannockburn
Build Stage 22 - The transmission
Parts required:
B, C and D from Parts 24, A from Parts 25.

Also required:

The plug is inserted into the tappet guide then the tappet guide is attached to the transmission case using a screw.

bugsec attached the following image(s):
060.jpg
061.jpg
Users browsing this topic
Guest (2)
4 Pages <1234>
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.304 seconds.
DeAgostini