Welcome Guest Search | Active Topics | Log In | Register

Rossi Yamaha YZR-M1 Official Build Diary - Pack 9 (UK) Options
Spal
#1 Posted : 02 March 2019 22:15:04

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Registered

Joined: 19/06/2013
Posts: 4,348
Points: 12,825
Location: West Yorkshire
Pack 9 contains parts for stages 32-35

Stage 32

Contents: Oil pump,Pump cover, Coupling

Locating the holes in the oil pump and the corresponding pins on its cover,press the two together.Retrieve the engine block and orientate it to show the three holes on the left side.Align the pins on the pump with the three holes, and then press it into place.Press the two ends of the coupling into position.

Stage complete, carefully store any remaining parts in a stage labelled bag.


Spal attached the following image(s):
IMGL2141.JPG
IMGL2142.JPG
IMGL2143.JPG
IMGL2144.JPG
IMGL2145.JPG
IMGL2146.JPG
IMGL2147.JPG
IMGL2148.JPG
Spal
#2 Posted : 03 March 2019 22:01:54

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Registered

Joined: 19/06/2013
Posts: 4,348
Points: 12,825
Location: West Yorkshire
Stage 33

Contents: Clutch bell,Last plate,First plate, Intermediate plates x3

Prepare the clutch bell and the first plate. The notch on the inside of the plate corresponds with the tab on the bell.Place the first plate onto the bell, fitting the tab on the bell into the notch on the plate.Now take the three intermediate plates, and locate the notch on the inside of each one. As with the first plate, these notches correspond to the tab on the bell.Place all three intermediate plates onto the bell before fitting the final plate onto the bell, inserting the two pins into the holes in the plate.

Stage complete, carefully store any remaining parts in a stage labelled bag.


Spal attached the following image(s):
IMGL2150.JPG
IMGL2151.JPG
IMGL2152.JPG
IMGL2153.JPG
IMGL2154.JPG
IMGL2155.JPG
Spal
#3 Posted : 04 March 2019 12:09:05

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Registered

Joined: 19/06/2013
Posts: 4,348
Points: 12,825
Location: West Yorkshire
Stage 34

Contents: Box,Tube,Clutch cover,Clutch ring,Clutch flange

Place the box onto the engine, inserting the pins into the holes. Push the end of the tube coming out of the cylinder head onto the circled pin on the box.Locate the two circled pins on the right hand side of the engine and push the ends of the tube supplied with this stage onto the two pins.Insert the pins of the clutch ring into the holes on the clutch cover. Fit the clutch flange onto the clutch cover, inserting the pins into the holes. Retrieve the clutch assembly from Stage 33 placing the clutch cover into place on the rest of the clutch to complete the assembly.Finally insert the two pins on the reverse of the clutch into the two holes in the side of the engine block.

Stage complete, carefully store any remaining parts in a stage labelled bag.


Spal attached the following image(s):
IMGL2158.JPG
IMGL2159.JPG
IMGL2160.JPG
IMGL2161.JPG
IMGL2162.JPG
IMGL2163.JPG
IMGL2164.JPG
IMGL2165.JPG
IMGL2166.JPG
IMGL2167.JPG
IMGL2168.JPG
IMGL2169.JPG
IMGL2170.JPG
IMGL2171.JPG
IMGL2172.JPG
Spal
#4 Posted : 05 March 2019 20:27:41

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Registered

Joined: 19/06/2013
Posts: 4,348
Points: 12,825
Location: West Yorkshire
Stage 35

Contents: Coolant hose,Coolant pipe,Starter motor base,Starter motor

Take the coolant pipe, and insert the two tabs on the underside into the two slots in the cylinder head cover, noting its orientation.Now push the coolant hose onto the end of the pipe.Insert the pins of the starter motor into the corresponding holes in the starter motor base, and push the parts together.Locate the two holes in the starter motor and the two pins on the engine.Press the starter motor into place, inserting the pins into the holes.

Stage complete, carefully store any remaining parts in a stage labelled bag.

Spal attached the following image(s):
IMGL2176.JPG
IMGL2177.JPG
IMGL2178.JPG
IMGL2179.JPG
IMGL2180.JPG
IMGL2181.JPG
IMGL2182.JPG
IMGL2183.JPG
IMGL2184.JPG
IMGL2185.JPG
IMGL2186.JPG
Users browsing this topic
Guest (2)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.109 seconds.
DeAgostini